Fun with Spray Paint

Hammered paint with appliance epoxy over.
Doesn't look like plastic -- more like enameled cast iron. 

Cosmetically, I'm having fun with this project. The bike when purchased was red, purple and rusty chrome.

So I have set out to rectify the appearance of the bike by eliminating as much chrome as possible and getting rid of the purple. The great thing about the VSTAR 650 Classic is how much of the bike is steel rather than plastic.

Those big sculpted front and rear fenders are made of metal and so I can sand it down to the metal and start from scratch. That said, the bike does have some cheap plastic bits on it and I don't like plastic.

At one point I removed the decals and painted the side covers with Rustoleum Hammered metal to get rid of that too-smooth plastic look. It worked great, but now I want the side covers to be black. I could strip off the old paint, but again, I don't want it to look like plastic when I'm done.

So I tried painting over the hammered with Rustoleum Appliance Epoxy - a paint intended for painting refrigerators but used successfully by motorcycle folks to get that powdercoat look without the cost.  I used it on the smooth plastic speedometer binnacle and very very happy with it. I wasn't sure how it would look over the hammered paint finish. Turns out, it looks pretty good -- if enameled cast iron is what you like. Beats plastic. I'm also using the same combo of Hammered with Appliance Epoxy over to make the cheap looking plastic covering the neck frame look less horrible. It is not a look for everyone, but I like it.

You can also see I'm playing around with some graphic ideas for the El Burro - I like the type above, but I think I'll try to mimic the sweep of the side covers somehow. Early days yet.

Another part of the bike I wanted to change was the rear tail lights -- It is kind of a droopy mustache looking thing that broke when we were getting the bike out of the truck. I've repaired it but always kinda hated it - it was rusty and funky looking. Over time, however, I've started liking it. It is very distinctive of the V-Star model line, and I've found it a neat way to identify other Vstars the road or in pictures.

The rusty chrome had to go, however, so I sprayed it with Plasti-dip. It actually doesn't look that bad -- the plastic stuff hiding the imperfections and even the electrical tape holding the left side up.

Meanwhile, the rest of the paint is coming together. I really like the Regal Red as it the layers get thicker. The earliest parts have already had clea rcoat and I started sanding with 1000 grit and polishing with the Mequiars Ultimate last night. (as demonstrated by this guy)  It looks great -- amazing for rattle can spray paint. Can't wait to see the tank and fenders with this finish.

Red Paint Going On

Paint is going on. Red and black. Of course some parts are already powder coated black. I used ultra hi-temp paint on the ugly pipes to blacken them up. They look pretty good. I was going to wrap them with pipe wrap, but the stock pipe layout doesn't really lend itself to that. If I upgrade my pipes down the line, I'll probably wrap those -- I hate chrome.

Here's a hint of what we're going to be looking at in the future. Red and black on the headlight and air cleaner, black pipes, red tank. You can see that I did the Key Mod of the Webslinger's website (RIP). I also coated the plastic neck guards in Rustoleum Hammered black to give them texture. The chrome driving lights and signals are coming off and will be replaced with matching red and black theme.

The first layer of red went on the tank today. It looks awful bright in this picture and there is still a lot of work to do.

I also took off the California emission can and ran the overflow hose down empty space where the can was before. I have the AIS holes all plugged.

Before I put the exhaust back on, I should probably pull the back wheel off and lube spine on the drive shaft. If I do that, there's a couple other projects I could also tackle -- the rear brake, painting the spokes, etc. The front end is the same story - new brake pads, clean the caliper and disc, paint the wheel and replace the brake line and fluid. I'm getting tempted to just put it all back together for a quick spring ride.   Oh well, it's only April. If I stay focused, I can still get a lot done before the sun comes out in July.

Paint and progress

The sun is starting to come out and the bikes are going by my house. It has been a short winter and I have lots of work left to do.

I am, however, making progress. I have my headlight bucket and fender rails powder coated gloss black and I  have my tank primed and sanded and read for the first coats of paint. Today I got the first coats of paint -- real paint -- on the highlight areas of the headlight bezel, the air cleaner and a few other trim pieces. It took a while to get the right red -- I wanted something dark, but that would still jump out. What I ended up with is Regal Red from Rustoleum - which is actually pretty close to the stock red. So far it looks good and glossy and I'm pretty excited about what the final product is going to look like.

I haven't settled on the paint job for my tank and fenders. That's why I'm focusing on trim pieces where I have a better idea. This is either going to be a red bike with black trim or a black bike with red trim.

AIS is gone. New pegs is on!

Meanwhile, I've been cleaning up the front of the bike. I took the AIS system off - a common mod -- and then noticed the California emisssions can on the other side. Turns out, I don't have an California tank, so I took that off too. Now the front of my bike has a cleaner, more open look without all the nanny-state plastics. That said, I could not get the AIS plugs out of the engine, so I sealed them off. The back plug elbow  broke off while I was trying to use the slide hammer to yank it out. So I sealed that up with some steel reinforced epoxy. The front one is sealed with a little bolt. I'll paint them black -- maybe put a little copper plumping cap on -- give it that steam engine look.


The two hoses left behind by the removal of the AIS and the Cali Can are plugged with a golf tee and a rollover valve respectively, but I might remove the rollover valve and extend the hose.

I also put on the new front pegs, which are much better than the bent ones that were on there previously. I took the exhaust off and discovered a lot of rust and dents. I bought all new gaskets and I'm giving it a nice coat of ultra hi-temp Rustoleum gloss black. My goal is to get it looking like an old un-restored bike - no chrome, just a tough old donkey ready to go anywhere.

I still have a lot to do. Even if the paint progress is encouraging, there are still a lot of projects left before I get on and ride. I have a braided brake line and new brake pads for the front. I need to take the rear wheel off and lube the splines of the main drive shaft. While I have the wheels off, I want to paint -- or plastidip -- them.

Ready to paint - I'm using a total of three
different kinds of primer on this project. 

Fenders are almost ready for paint.
Another coat of primer and some sanding first. 

Good bye rusty pipes. 

This is my blank canvas.